CSNI0037 LOBI/A2-77A. (Abstract last modified 22-MAY-1992)
1.
NAME OR DESIGNATION - LOBI/A2-77A. 2.
COMPUTER FOR WHICH PROGRAM IS DESIGNED AND OTHER MACHINE VERSION PACKAGES AVAILABLE -
To request or retrieve programs click on the one of the active versions below.
A password and special authorization is required. Explanation of the status codes.
Machines used:
Package-ID Orig.Computer Test Computer
CSNI0037/01 Many Computers
3.
DESCRIPTION OF TEST FACILITY - The LOBI-MOD2 test facility is a high pressure integral system blowdown refill test facility designed, constructed and operated at the Joint Research Centre of the European Communities, Ispra Establishment, Italy. It represents and extensive modification of the original MOD1 configuration and was put into operation after June 1982. 4.
DESCRIPTION OF TEST - Test A2-77A represents one of the first experiments of the LOBI-MOD2 Small Leak Programme, which was started in April 1984. It is designed to establish the natural 5.
EXPERIMENTAL LIMITATIONS OR SHORTCOMINGS - 6.
PHENOMENA TESTED - Natural circulation in 1- and 2-phase flow; asymmetric loop behaviour; phase separation; ECC mixing and condensation; heat transfer; 1- and 2-phase pump behaviour. 7.
SPECIAL FEATURES OF EXPERIMENT - LOBI's large size and full height components are considered an advantage. 8.
COUNTERPART EXPERIMENTS - Semiscale. 9.
STATUS 10.
REFERENCES - 11.
TEST DESIGNATION - A2-77 12.
PROGRAMMING LANGUAGE(S) USED - 15.
ESTABLISHMENT - 16.
MATERIAL AVAILABLE - 17.
CATEGORIES - Keywords: BLOWDOWN, DATA, LOSS-OF-COOLANT ACCIDENT, TRANSIENTS
Program-name Package-ID Status
LOBI/A2-77A CSNI0037/01 Arrived
The LOBI facility is a 1/700 scale model of a four loop PWR and has two primary loops, the intact loop representing three loops and the broken loop representing one loop of a four-loop PWR. The reactor pressure vessel model contains an electrically heated rod-bundle with 64 rods and a heated length of 3.9 m. The nominal heating power is 5.3 MW. The downcomer is of annular shape. An upper head simulator is connected to the vessel. Each of the two primary loops contains a pump and a steam generator. The different mass flows in the loops are established by different pump speeds, since the two pumps are identical. ECC water can be supplied from two accumulators, one for each loop. Cold or hot leg as well as combined injection can be simulated. Heat is removed from the steam generators by a secondary system.
In the MOD2 configuration, emergency core cooling (ECC) water can be supplied by the high pressure injection system (HPIS) and by the accumulator injection system (AIS).
The LOBI test facility is the only high pressure integral test facility within the European Communities (1982), built and operated in the Joint Research Centre, Ispra, ITALY. In the LOBI experiments the thermal-hydraulic behavior of the facility during a transient, caused by a simulated loss of coolant accident (LOCA), is investigated to provide an experimental basis for analytical model development and code verification.
circulation behaviour of the LOBI-MOD2 primary loop under single phase and two phase flow conditions without rupture in the primary loop.
CSNI0037/01: 22-MAY-1992 Arrived at NEADB
CSNI0037/01:
- G. De Santi and G. Leva:
Quick Look Report on LOBI Test A2-77A
ISPRA LQC 85-32 Communication No. 4029, December 1985
- E. Ohlmer and J. Sanders:
Experimental Data Report on LOBI Test A2-77A
ISPRA LEC 85-33, Communication No. 4024, April 1985
- W. Kolar and W. Brewka:
LOBI Experimental Data Tape - Format Description -
Technical Note No.I.06.C1.85.49 (May 1985)
- LOBI Project - RELAP5 Base Input Data for LOBI-MOD2
LPC 85-18 (February 1985)
CSNI0037/01:
Commission of the European Communities
Joint Research Centre
Ispra Establishment
I-21020 Ispra
ITALY
CSNI0037/01:
NATURAL CIRCULATION AT 90 6,006Kbytes
NATURAL CIRCULATION AT 75 5,961Kbytes
- Y. Integral Experiments Data, Databases, Benchmarks
Home - About Us - Work Areas - Data Bank - Publications - Press Room - List of acronyms - Search